Products are listed alphabetically.

Page 1 of 3    Next page »

1. ADAPTIVE FIXTURES KIT (MODEL AF-10-K) The Adaptive Fixtures Kit is a switch mounting hardware kit designed for use as a replacement program or as an eveluation tool for properly mounting switches. The Kit is comprised of multi-purpose pieces and parts that can be used as "on the spot" replacement and sent on with the user. You can then reorder the parts as necessary to replace what has been used. The Kit can also be used as an evaluation tool where the parts never leave the Kit. Mountings can be experimented with to find a particula...[More Information]
   
   
2. ADJUSTABLE WHEELCHAIR / BEDRAIL CLAMP (MODEL 2026) The Adjustable Wheelchair/Bedrail Clamp, model 2026, is switch mounting hardware designed to aid in attaching switches to wheelchairs and workstations. This clamp tightens using a large knob....[More Information]
   
   
3. ALUMINUM MOUNTING RODS (MODELS 2062 & 2063) The Aluminum Mounting Rods are switch mounting hardware designed to aid in attaching switches to wheelchairs and workstations. All models are aluminum. DIMENSIONS: Model 2062 is 3/8-inch in diameter and 12 inches long and model 2063 is 0.25-inch in diameter per foot....[More Information]
   
   
4. ANCHORED JOYSTICK AND BUTTON COMPUTER CONTROL INPUT INTERFACE ----CUSTOM ADAPTATION ---- PURPOSE: To provide a child with cerebral palsey with a stable interface to control a computer. A commercially available joystick and large button is used in place of a mouse and keyboard to control a computer. A metal plate and screwed stud is attached to the bottom of the base of the joystick. A hole is drilled in the child's desk, and the stud is screwed into a second plate on the underside of the desk. A nut holds the assembly in place while the joystick is in use....[More Information]
   
   
5. ARMREST MOUNTING BRACKET (MODEL 3395) Used in ocnjunction with a standard hand-control clamp for mounting a Model 3185 joystick for hand operation. Consists of a 1/2 inch diamter stainless steel mounting rod fitted to a 3/4 inch diamter mounting shaft to permit a wide range of joystick positioning....[More Information]
   
   
6. ARTICULATING ARM (MODEL H-1) The Articulating Arm is switch mounting hardware designed to enable control switches and communicators to be placed in virtually any position for individuals with upper extremity or severe physical disabilities. The adjustable arm attaches to a table, wheelchair, bed rail, etc. Three knobs permit adjustability and lock the unit in position....[More Information]
   
   
7. ASL EGG SWITCH FINGER RING MOUNT (MODEL ASL300R) The ASL Egg Switch Finger Ring Mount, model ASL300R, is switch mounting hardware designed for use by individuals with cerebral palsy or neurological or upper extremity disabilities. This mount for the ASL 300 Egg Switch (not included; see separate entry) holds the Egg Switch near the user's finger. Screws for the switch are included. OPTIONS: Egg switch (model ASL 300)....[More Information]
   
   
8. BIB KIT (MODEL 3390) Used for mounting a Model 3185 joystick for chin operation. The bib uses velcro straps to secure the bib around the neck and rib cage, and incorporates adjustable mounting harware to permit a wide range of joystick positioning....[More Information]
   
   
9. BIG BEND CLIP The Big Bend Clip is a bookholder, document holder, or switch mounting hardware designed for use by individuals with upper extremity disabilities. This device consists of an adjustable clamp base with an expandable gooseneck-style flexible arm attached to a large alligator clip. This unit can be clamped to the Convert-Able Table (see separate entry), a wheelchair tray, or other flat surface to hold books, toys, photographs, switches, and other items. Using two clips enables larger, heavier items...[More Information]
   
   
10. C-CLAMP WITH SWIVEL (MODEL 2018) The C-Clamp with Swivel, model 2018, is switch mounting hardware that attaches to most surfaces for indiviudals who use switches. The unit consists of a universal swivel clamp mounted to a C-clamp, allowing attachment of 1/4-inch rods and accessories. Mounting switches enables users to activate switches in different positions rather than having to use the switches mounted on a flat surface....[More Information]
    
    
11. COLLAR & BRIDGE ASSEMBLY (MODEL 32669) The Collar & Bridge Assembly, model 32669, is a control switch accessory for mounting hardware designed to secure wheelchair controllers to the chair. The Collar allows a full range of motion while holding controllers such as joysticks and sip-n-puff goosenecks in a stationary position relative to the user. The Bridge Assembly includes plastic spacers to position the control unit at a proper distance from the collar. Pre-drilled holes on the front of the collar enable a variety of height adjustm...[More Information]
    
    
12. DAESSY MINI BENT-TUBE MOUNT (MODEL M75-BTM) The DAESSY Mini Bent-Tube Mount, model M75-BTM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. This product also can be removed from the wheelchair when not needed. The frame clamp assembly includes a...[More Information]
    
    
13. DAESSY MINI FOLDING MOUNT (MODEL M75-FM) The DAESSY Mini Folding Mount, model M75-FM, is a stand for a tablet computer, switch mounting hardware and a computer and communicator mounting kit for wheelchair designed for use by individuals with use of only one hand, or mobility, lower extremity or upper extremity disabilities, or spinal cord injury. The mount is non-directional and can be installed on either side of the wheelchair. The system folds the horizontal tube down to the outside. The folding joint between the two mount tubes brin...[More Information]
    
    
14. DUAL-LOCK Dual-Lock is a surface anchor designed to mount switches and other devices to mounting plates or any other surface. When pressed together, this adhesive-backed strip provides a tough, secure bond. DIMENSIONS(W x L): 2 inches x 1 foot. WARRANTY: A manufacturer's warranty is available on this product....[More Information]
    
    
15. FLEX MOUNTING (MODEL 1540) Flex Mounting, model 1540, is switch mounting hardware designed for indivudals who use switches, specifically headswitches. When a headswitch or other touch switch is attached to this spring mounting, it will automatically return to its original position if moved by inadvertent gestures. DIMENSIONS: The Flex Mounting comes with a 1/4-inch diameter mounting rod, approximately 18 inches long....[More Information]
    
    
16. GOOSENECK MOUNTING SYSTEM (MODELS 1550 & 1565) The Gooseneck Mounting System is switch mounting hardware designed to enable control switches to be optimally positioned. Equipped with a flexible, extra-stiff gooseneck, the system can be attached to a table or wheelchair with the one-piece all-surface clamp or the switch (not included) can be attached to the circular plate w3ith the included dual-lock fastening strips. Model 1550 also has a locking swivel balljoint under the mounting plate for more precise angle adjustment. DIMENSIONS: The cir...[More Information]
    
    
17. HEAD MOUNTING KIT (MODEL A72) The Head Mounting Kit, model A72, is switch mounting hardware designed for mounting the Plate Switch or L.T. Switch (see separate entries) on wheelchairs for use by persons with good head control. The kit includes a mounting plate, a right-angle tube, 13-inch flexible goosneck, push button disconnect, and a wheelchair clamp. The pushbutton disconnect is for quick removal of the unit from the wheelchair. Instructions are also included....[More Information]
    
    
18. HEADREST SWING AWAY BRACKET (SM-HRSA240) The Headrest Swing Away Bracket, model SM-HRSA240, is switch mounting hardware designed for use by individuals who use wheelchair headrests. This arm attaches to any Stealth or Otto Bock style headrest (see entries). It is made ready to mount an egg switch or a sensor in a spot pad. Once adjusted in place the user can swing it away when it is not needed and push it back to the same spot when needed....[More Information]
    
    
19. HEADSWITCH KIT 1 (MODEL 1560) The Headswitch Kit 1, model 1560, is a touch switch and switch mounting hardware package. HEADSWITCH: (Model 705) this switch (with cord) is activated with very light pressure from the head, but can also be activated by a knee, elbow, cheek, or other body part when mounted on a table or wheelchair. MOUNTING HARDWARE: The mounting hardware in the kit includes all necessary components: 1 universal swivel clamp, one 3/4 - 1/4 inch adapter, one 8-inch rod, one 18-inch rod, and one wheelchair clamp....[More Information]
    
    
20. HEADSWITCH KIT 2 (MODEL 1570) The Headswitch Kit 2, model 1570, is a switch mounting hardware and touch switch package that includes all necessary components for the attachment of the switch to a table or flat surface. HEADSWITCH: Headswitch model 705 is a touch switch that can also be activated by very light pressure from the knee, elbow, cheek, or other body part. MOUNTING HARDWARE: 1 universal swivel clamp, one 3/4 - 1/4 inch adapter, one 8-inch rod, one 18-inch rod, and one surface mount clamp....[More Information]
    
    
21. HEADSWITCH KIT 3 (MODEL 1580) The Headswitch Kit 3, model 1580, is a touch switch and switch mounting hardware package. HEADSWITCH: Headswitch (model 705) is a touch switch that can be activated with very light pressure from the head, knee, elbow, cheek, or other body part. 2 headswitches and cords are included in this kit. MOUNTING HARDWARE: Two 3/4 - 1/4 inch adapters, 1 flex mount, 8 assorted rods (4 pairs), 2 quick disconnects, 2 surface mount clamps, 2 wheelchair clamps, 4 universal swivel clamps, and 1 sturdy case with...[More Information]
    
    
22. HEAVY-DUTY TRIANGULAR FLANGE (MODEL 2002) The Heavy-duty Triangular Flange, model 2002, is switch mounting hardware designed to aid in attaching switches to wheelchairs and workstations. The flange is a 5/8-inch 27 female connector....[More Information]
    
    
23. HEAVY-DUTY WEIGHTED BASE (MODEL 2008) The Heavy-duty Weighted Base, model 2008, is switch mounting hardware designed to aid in attaching switches to wheelchairs and workstations. DIMENSIONS: Six inches in diameter....[More Information]
    
    
24. INTERCONNECTING ADAPTERS (MODELS 2022, 2023, & 2024) The Interconnecting Adapters are switch mounting hardware designed to aid in attaching switches to wheelchairs or workstations. Model 2022 is a 0.25-inch 20 stud adapter. Model 2023 is a 5/8-inch internal adapter woth 0.25-inch 20 bushing. Model 2024 is 5/8-inch 27 bushing tube adapter....[More Information]
    
    
25. LABAC MOUNTING KIT (MODEL 3515) Used for mounting a head operated actuator to the back of a Labac recliner. The mounting kit consists of a mounting bar with a stop clamp, a C-mounting rod, and a rod clamp to join the mounting rod to the mounting bar. Permits the actuator to be removed from the recliner, and returned to its original position without the need to readjust the mounting....[More Information]
    
    

Page 1 of 3    Next page »