Products are listed alphabetically.

Page 1 of 2    Next page »

1. ABDUCTOR FLIP DOWN KIT (MODEL 31467) The Abductor Flip Down Kit, model 31467, is seating hardware general designed to allow abductors and lateral pads to swing away during wheelchair transfers. Designed to be used with the manufacturer's Abductor Pads or Lateral Pads (see separate entries), this kit includes one four-inch coated steel tapered L-bracket, one 2.75-inch coated steel slotted L-bracket, one 2.75-inch coated steel extrender, one anodized aluminum hinge, and mounting hardware. COLOR: Black....[More Information]
   
   
2. ADJUSTABLE BRACKET -- SINGLE, THREE, FIVE, SEVEN & NINE HOLES. The Adjustable Brackets are wheelchair seating hardware used in many areas such as wheelchair seat construction and wheelchair seat positioning with seat hooks. Made of stainless steel, both ends are rounded. One end is punched with two 17/64 inch x 5/8 inch slots and the other with a selected number of ##10 through holes. They are deburred for a smooth finish. Brackets are available with one, three, five, seven, or nine holes. COLOR: Available in black and stainless steel....[More Information]
   
   
3. ADJUSTABLE J HOOK BRACKET HARDWARE SEATING PACKAGE (PACKAGE 20XX) The Adjustable J Hook Bracket Hardware Seating Package, package 20XX, is seating hardware designed for use on a wheelchair. The Package includes a solid back insert including T-nuts; a solid seat insert including T-nuts; a wide, 1.5-inch offset seat to back hinge; a pair of 1- inch diameter tube two-hole J hooks; a pair of five-hole adjustable L brackets; a pair of 1-inch diameter tube six-hole J hooks; a pair of two-hole adjustable L brackets; a 1-inch diameter tube drop stop; and a 1-inch diam...[More Information]
   
   
4. ADJUSTABLE-DROP HARDWARE KITS (MODELS 32517 & 32518) Adjustable-Drop Hardware Kits are seating hardware general designed to attach drop seats to wheelchairs. The kits include four J-brackets, four L-brackets, and screws and locking nuts needed to adjust the brackets and to secure the brackets to the Drop Seat (see separate entry). The hardware in the Kits can be raised and lowered to adjust the Drop Seat. DIMENSIONS: Model 32517 fits chairs with 7/8-inch tubes and model 32518 fits chairs with one-inch tubes....[More Information]
   
   
5. BALL RATCHET SET The Ball Ratchet Set is a seating hardware allowing angle adjustment in 5 degree increments. It is made of cast and heat treated alloy steel. It can be bolted or welded inside 7/8 inch diameter by 18 gauge round tubing. The Set is useful for legrests, seat to back attachments, and other seating applications. It is available in chromed or unchromed....[More Information]
   
   
6. CLAMP-- POSITIONING, SWIVEL HOLD DOWN, FIXED HOLD DOWN These Clamps are seating hardware designed to be used in wheelchair seating systems. The Positioning Clamp has applications where clamping of the mounting hardware is fastened to the tubing of the wheelchair. It is most often used on the rear of the wheel base to position the chair initially and to keep the chair from shifting. The Swivel Clamp is a riveted one-piece design, used for securing the seat to the wheel base or wheelchair. By turning the swivel hold-down 90 degrees, complete seating d...[More Information]
   
   
7. EQUIPMENT FOR USE IN POSTURAL SEATING PROGRAMS FOR DISABLED PERSONS Full range of brackets and mounting hardware for building custom seating systems for wheelchairs and other positioning devices. Includes frame interface hardware for use with Canadian Wheelchair's Mooney base. Most hardware made from chrome-plated steel, with quick release and adjustable features....[More Information]
   
   
8. FIGURE-8 CLAMP (MODELS 32310 & 32310B) The Figure-8 Clamp is a seating hardware and a mounting clamp for accessories designed for use with wheelchairs. The two-part clamp is used to attach controls, accessories, and other devices to wheelchairs. One side of the clamp accommodates .75-inch tubing and the other side accommodates 7/8 inch tubing. Deep-set cap screws are used to tighten clamp around tubing. Set screws can provide additional mounting stability. COLOR: Model 32310B comes in black. WARRANTY: The manufacturer warrants this p...[More Information]
   
   
9. FIXED-DROP HARDWARE KITS (MODELS 32617H, 32618H, 32542H, 32603H, 32604H & 32543H) Fixed-Drop Hardware Kits are seating hardware general designed to attach drop seats to wheelchairs. The kits include four drop hooks, eight washers, and eight socket head screws. DIMENSIONS: Models 32617 and 32603 create a one-inch drop. Models 32618H and 32604H create a two-inch drop. Models 32542H and 32543H create a three-inch drop. Models 32617H, 32618H, and 32542H fit chairs with 7/8-inch tubes. The other models fit chairs with one-inch tubes....[More Information]
   
   
10. FLIP DOWN KIT WITH ABDUCTOR PAD (MODELS 31468S, 31468M, & 31468L) The Flip Down Kit With Abductor Pad is seating hardware general and an abductor pad designed to aid in positioning individuals who use wheelchairs. This kit includes an abductor pad, one four-inch coated steel tapered L-bracket, one 2.75-inch coated steel slotted L-bracket, one 2.75-inch coated steel extrender, one anodized aluminum hinge with push-button release, and mounting hardware. The Abductor Pad is made of textured urethane self-skinning foam and come with 10-32 T-nuts embedded in all m...[More Information]
    
    
11. GROWTH LINKS & DIAL LINKS (MODEL GL01 THROUGH GL06 & GL10) Growth Links (Model GL01 thru GL06) and Dial Links (GL10) are hardware designed for attaching seats and backs. They are designed to be used with aluminum pans, but Wood Adaptors (Model GL21, $40/pair) are available for mounting to wooden panels. The links come in pairs and have adjustable angles. Growth links are to be used when back is supported by separate frame. Dial links support back independently....[More Information]
    
    
12. HEADREST HARDWARE (100 SERIES) The Headrest Hardware, series 100, is seating hardware designed for use on wheelchairs. Each hardware kit includes link hardware and offers a wide range of adjustment. This hardware offers five points of adjustability. COLOR: All hardware is black chromed and anodized. ...[More Information]
    
    
13. INDIVIDUAL HARDWARE This set of Individual Hardware is part of the manufacturers' seating and positioning system for persons in a wheelchair. The set includes a full line of hardware for attaching seats, backs, trunk pads, and headrests. The hardware comes in stainless steel or aluminum....[More Information]
    
    
14. INTERFACE HARDWARE (MODELS 442F2 & 442F1) The Interface Hardware, models 442F2 and 442F1, is seating hardware designed to allow mounting of Otto Bock seating systems into Maclaren or Pogon strollers or wheelchairs ranging from 10 to 18 inches wide. A spring-loaded plunger mechanism allows quick removal of the seat for transfer into another base or for transporting. Custom interfaces are available to accommodate mounting systems on most power bases and scooters....[More Information]
    
    
15. LATERAL EXTENSION BRACKET The Lateral Extension Bracket is torso support hardware designed for individuals with neurological or severe physical disabilities or cerebral palsy. The bracket expands the range in which seating supports can be adjusted laterally. The unit is attached at the end of the adjustment slot of the existing trunk lateral brackets and provides almost 3 extra inches of width adjustment for growing children and other individuals who need extra expansion of their seating system. This bracket bolts to mo...[More Information]
    
    
16. MILLER'S COMPLETE SUPPORT SYSTEMS The Miller's Complete Support Systems are lateral trunk support components designed to be mounted off the seat, back insert, modular pan, or wheelchair frame, depending on the application, to give support to the trunk and pelvic areas or to provide adduction. Components of the seat, back, or pan-mounted systems include fixed, swing-away, and multiplane inserts, pads, and doglegs. The doglegs allow approximately 2 additional inches of lateral adjustment. The Multi Plane provides greater flexibili...[More Information]
    
    
17. MILLER'S MOUNTING HARDWARE COMPONENTS The Miller's Mounting Hardware Components are designed for affixing wheelchair accessories to solid seat and back panels or to 7/8 and 1 inch wheelchair frame tubing. Fixed, swingaway, and adjustable type clamps and brackets are available. COLOR: Silver or black chrome finish....[More Information]
    
    
18. MOTORIZED WHEELCHAIR SEAT SHIFTING SYSTEM ------ PROTOTYPE --------- PURPOSE: To create a prototype of a wheelchair seat that aids wheelchair users to change his or her seated position periodically. Changing position when seated for a long period of time is especially important for wheelchair users who spend almost every making moment seated. Failure to do so can result in deformities, bedsores, or considerable pain. The Swiss research group, Empa, is working with an ergonomics company to develop a new type of wheelchair seat that perio...[More Information]
    
    
19. MULTI-AXIS OFFSET HEADREST ASSEMBLY (MODEL 32465) The Multi-Axis Offset Headrest Assembly, model 32465, is seating hardware designed to attach offset headrests to standard wheelcahair frames. The entire assembly is designed to be used with small, large, combination, small lateral support, and neck rest style headrests (headrests sold separately). The heavy-duty assembly features an offset block that swivels on a ball for headrest adjustment in any direction, a straight bar that adjusts horizontally, a heavy-duty mounting ring, a durable mounti...[More Information]
    
    
20. OTTO BOCK TALL BACK AND MODULAR BACK HEADREST MOUNTING KIT & OTTO BOCK HEADREST ADAPTER KIT The Otto Bock Tall Back and Modular Back Headrest Mounting Kit ($5) and the Otto Bock Headrest Adapter Kit ($20) are headrest accessories that allow attachment of Otto Bock headrest mounting hardware directly to the Jay Back cushion, compensating for the contour of the cushion....[More Information]
    
    
21. POSITIONING HARDWARE Positioning Hardware is seating hardware general designed for attaching positioning aids to wheelchairs. Available items include two-, four-, six-, and eight-hole adjustment hooks; drop hooks; drop hooks for thigh pad inner mount; drop hooks for thigh pad outer mount; side, bottom, and parallel flanges; latch tabs; universal rear bracket; and a swing tab U-bracket. Also available is a seatlock; a seatblock; a headrest mounting plate; a child's headrest support; an adult headrest support; and six...[More Information]
    
    
22. SEAT AND BACK MOUNTING HARDWARE, DROP HOOKS, DROP HOOK STOPS, BACK TO SEAT BRACKETS Complete line of seating hardware for mounting backs, seats, lateral trunk supports, abductors, headrests, leg and footrests in wheelchairs and other mobility bases. Adjustable and non-adjustable, knob-release and drop hook styles. May be ordered in complete kits or by individual components. Optional components $93.00 to $2.00....[More Information]
    
    
23. SEAT HOOK, ADJUSTABLE-SINGLE HOLE, TWO HOLE, FIVE HOLE, SEVEN HOLE The Adjustable Seat Hooks are designed to serve a variety of extended wheelchair seat positioning applications, such as angling or height adjustment. These stainless steel hooks are countersunk for a ##10 flathead screw. DIMENSIONS: The hooks are 0.75-inch wide and are available to fit tubes 0.75 inch, 7/8 inch, 1 inch, or 1 3/16 inch in diameter. COLOR: Available in black or stainless steel...[More Information]
    
    
24. SEAT HOOK, DROP The Seat Hook, Drop is one-piece seating hardware designed for lowering and leveling a wheelchair seat. It is made of stainless steel and fabricated with two 17/64 inch x 5/8 inch mating slots. Both ends are curved and deburred for a smooth finish. DIMENSIONS: The hook ends fit tubes 0.75 inch, 7/8 inch, 1 inch or 1 3/16 inches in diameter. The drop offsets range from 1 inch to 6 inches in 1-inch increments. COLOR: Available in black or stainless steel....[More Information]
    
    
25. SEAT HOOK, LIFT The Seat Hook, Lift is seating hardware designed to lift and level wheelchair seats. It is made of stainless steel and fabricated with two 17/64 inch x 5/8 inch mating slots. Both ends are rounded and deburred for a smooth finish. DIMENSIONS: The hook fits tubing 0.75 inch, 7/8 inch, 1 inch or 1 3/16 inches in diameter. The lift offset ranges from 0 inches, 0.5 inch, or 1 inch to 2 inches. COLOR: Available in black or stainless steel....[More Information]
    
    

Page 1 of 2    Next page »